Hydrofluorocarbon (HFC) Prohibitions in California
Contact
Categories
What HFCs are prohibited in California and why?
California is required to reduce HFC emissions 40 percent below 2013 levels by 2030 under Senate Bill 1383 (Health & Saf. Code § 39730.5). HFCs are synthetic gases that are used in a variety of applications, but mainly to replace ozone-depleting substances in aerosols, foams, refrigeration and air-conditioning. HFCs have a powerful impact on climate as they trap heat in the atmosphere at a rate thousands of times that of carbon dioxide.
To help meet the HFC reduction goal, California adopted the same prohibitions that were previously in place at the federal level through the California Cooling Act (Senate Bill 1013, Health & Saf. Code § 39734) and through a regulation approved by the California Air Resources Board (Cal. Code Regs., tit. 17, §§ 95371, et seq). The federal prohibitions California adopted under SB 1013 originated from the United States Environmental Protection Agency’s (U.S. EPA) Significant New Alternative Policy (SNAP) Program, Rules 20 and 21, which were partially vacated in 2017. Similar to the federal SNAP Rules, the California prohibitions are end-use and sector-specific.
To provide clarity to the regulated community, the California Air Resources Board (CARB) took action to consolidate the California regulation (previously Cal. Code Regs., tit. 17, §§ 95371-95377) and the statute (SB 1013, Health and Saf. Code § 39734) into one place. CARB incorporated the SB 1013 statutory provisions into the regulation under a provision of the law that allows for statutory changes to be incorporated into regulations without an additional rulemaking (Cal. Code of Regs., tit. 1, § 100). These are called “changes without regulatory effect” – meaning they only incorporate SB 1013 as is already in place and do not add or remove any requirements that are not already law. This added one additional section to the numbering structure (now Cal. Code Regs., tit. 17, §§ 95371-95378). The regulation can be found here.
For a summary of the HFC prohibitions and the effective dates, see the table below. The effective dates provided refer to the date the aerosol, foam, or equipment was manufactured. This table is not meant as a substitute for reading the laws and regulations and does not expand or change the laws and regulations. Please see Health and Safety Code section 39734 and California Code of Regulations, title 17, sections 95371, et seq. for more information.
This Factsheet only identifies HFCs. Prohibitions on manufacture and sale of chlorofluorocarbons, hydrochlorofluorocarbons, methylene chloride, and other non-HFC substitutes are not included. For these prohibitions, please reference the law.
Learn more about CARB’s strategy for reducing HFCs and other short-lived climate pollutants.
The following tables contain HFC prohibitions for both Senate Bill 1013 and the CARB HFC Regulation.
Aerosols
End-Use | Prohibited Substance | Effective Date |
---|---|---|
Aerosol | HFC-125 | Unacceptable as of January 1, 2019. |
Aerosol | HFC-134a | Unacceptable as of January 1, 2019 except for uses listed as acceptable, subject to use conditions. |
Aerosol | HFC-227ea and blends of HFC-227ea and HFC‑134a | Unacceptable as of January 1, 2019 except for uses listed as acceptable, subject to use conditions. |
Foams
End-Use | Prohibited Substance | Effective Date |
---|---|---|
Rigid Polyurethane and Polyisocyanurate Laminated Boardstock | HFC‑134a, HFC‑245fa, HFC‑365mfc and blends thereof | Unacceptable as of January 1, 2019 except where allowed under narrowed use limits for military or space- and aeronautics-related applications.2 Unacceptable for military related applications as of January 1, 2022. Unacceptable for space- and aeronautics-related applications as of January 1, 2025. |
Flexible Polyurethane | HFC-134a, HFC-245fa, HFC-365mfc, and blends thereof | |
Integral Skin Polyurethane | HFC-134a, HFC-245fa, HFC-365mfc, and blends thereof; Formacel TI, and Formacel Z-6 | |
Polystyrene Extruded Sheet | HFC-134a, HFC-245fa, HFC-365mfc, and blends thereof; Formacel TI, and Formacel Z-6 | |
Phenolic Insulation Board and Bunstock | HFC-143a, HFC-134a, HFC-245fa, HFC-365mfc, and blends thereof | |
Rigid Polyurethane Slabstock and Other | HFC-134a, HFC-245fa, HFC-365mfc and blends thereof; Formacel TI, and Formacel Z-6 | |
Rigid Polyurethane Appliance Foam | HFC-134a, HFC-245fa, HFC-365mfc and blends thereof; Formacel TI, and Formacel Z-6 | Unacceptable as of January 1, 2020 except where allowed under narrowed use limits for military or space- and aeronautics-related applications. 2 Unacceptable for military related applications as of January 1, 2022. Unacceptable for space- and aeronautics-related applications as of January 1, 2025. |
Rigid Polyurethane Commercial Refrigeration and Sandwich Panels | HFC-134a, HFC-245fa, HFC-365mfc, and blends thereof; Formacel TI, and Formacel Z-6 | |
Polyolefin | HFC-134a, HFC-245fa, HFC-365mfc, and blends thereof; Formacel TI, Formacel Z-6 | |
Rigid Polyurethane Marine Flotation Foam | HFC-134a, HFC-245fa, HFC-365mfc and blends thereof; Formacel TI, and Formacel Z-6 | |
Polystyrene Extruded Boardstock and Billet (XPS) | HFC-134a, HFC-245fa, HFC-365mfc, and blends thereof; Formacel TI, Formacel B, and Formacel Z-6 | Unacceptable as of January 1, 2021 except where allowed under narrowed use limits for military or space- and aeronautics-related applications. 2 Unacceptable for military related applications as of January 1, 2022. Unacceptable for space- and aeronautics-related applications as of January 1, 2025. |
Rigid polyurethane high-pressure two-component spray foam | HFC-134a, HFC-245fa, and blends thereof; blends of HFC365mfc with at least 4 percent HFC-245fa, and commercial blends of HFC-365mfc with 7 to 13 percent HFC-227ea and the remainder HFC-365mfc; and Formacel TI | Unacceptable for all uses as of January 1, 2020, except where allowed under narrowed use limits for military or space- and aeronautics-related applications.[1] Unacceptable for military or space- and aeronautics related applications as of January 1, 2025. |
Rigid polyurethane low-pressure two-component spray foam | HFC-134a, HFC-245fa, and blends thereof; blends of HFC‑365mfc with at least 4 percent HFC-245fa, and commercial blends of HFC-365mfc with 7 to 13 percent HFC-227ea and the remainder HFC-365mfc; and Formacel TI[2] | Unacceptable for all uses as of January 1, 2021, except where allowed under narrowed use limits for military or space- and aeronautics-related applications.[3] Unacceptable for military or space- and aeronautics related applications as of January 1, 2025. |
Rigid Polyurethane one-component foam sealants | HFC-134a, HFC-245fa, and blends thereof; blends of HFC‑365mfc with at least 4 percent HFC-245fa, and commercial blends of HFC-365mfc with 7 to 13 percent HFC-227ea and the remainder HFC-365mfc; and Formacel TI[4] | Unacceptable, as of January 1, 2020. |
Retail Food Refrigeration
End-Use | Prohibited Substance | Effective Date |
---|---|---|
Supermarket Systems (Retrofit) | R‑404A, R‑407B, R‑421B, R‑422A, R‑422C, R‑422D, R‑428A, R‑434A, R‑507A | Unacceptable as of January 1, 2019. |
Supermarket Systems (New) | HFC‑227ea, R‑404A, R‑407B, R‑421B, R‑422A, R‑422C, R‑422D, R‑428A, R‑434A, R‑507A | Unacceptable as of January 1, 2019. |
Remote Condensing Units (Retrofit) | R‑404A, R‑407B, R‑421B, R‑422A, R‑422C, R‑422D, R-428A, R‑434A, R‑507A | Unacceptable as of January 1, 2019. |
Remote Condensing Units (New) | HFC‑227ea, R‑404A, R‑407B, R‑421B, R‑422A, R‑422C, R‑422D, R‑428A, R‑434A, R‑507A | Unacceptable as of January 1, 2019. |
Stand-Alone Units (Retrofit) | R‑404A, R‑507A | Unacceptable as of January 1, 2019. |
Stand-Alone Medium-Temperature Units[5] with a compressor capacity below 2,200 Btu/hour and not containing a flooded evaporator (New) | FOR12A, FOR12B, HFC‑134a, HFC‑227ea, KDD6, R125/290/134a/600a (55.0/1.0/42.5/1.5), R‑404A, R‑407A, R‑407B, R‑407C, R‑407F, R‑410A, R‑410B, R‑417A, R‑421A, R‑421B, R‑422A, R‑422B, R‑422C, R‑422D, R‑424A, R‑426A, R‑428A, R‑434A, R‑437A, R‑438A, R‑507A, RS‑24 (2002 formulation), RS‑44 (2003 formulation), SP34E, THR-03 | Unacceptable as of January 1, 2019. |
Stand-Alone Medium-Temperature Units with a compressor capacity equal to or greater than 2,200 Btu/hour and Stand-Alone Medium-Temperature Units containing a flooded evaporator (New) | FOR12A, FOR12B, HFC-134a, HFC-227ea, KDD6, R125/290/134a/600a (55.0/1.0/42.5/1.5), R‑404A, R‑407A, R-407B, R‑407C, R‑407F, R‑410A, R‑410B, R-417A, R‑421A, R‑421B, R‑422A, R‑422B, R‑422C, R‑422D, R‑424A, R‑426A, R‑428A, R‑434A, R‑437A, R-438A, R-507A, RS‑24 (2002 formulation), RS‑44 (2003 formulation), SP34E, THR‑03. | Unacceptable as of January 1, 2020. |
Stand-Alone Low-Temperature Units[6] (New) | HFC‑227ea, KDD6, R‑125/290/134a/600a (55.0/1.0/42.5/1.5), R‑404A, R‑407A, R‑407B, R‑407C, R‑407F, R‑410A, R‑410B, R‑417A, R‑421A, R‑421B, R-422A, R‑422B, R‑422C, R‑422D, R‑424A, R‑428A, R-434A, R‑437A, R‑438A, R‑507A, RS‑44 (2003 formulation) | Unacceptable as of January 1, 2020. |
Retail food refrigeration – refrigerated food processing and dispensing equipment (new) | HFC‑227ea, KDD6, R‑125/290/134a/600a (55.0/1.0/42.5/1.5), R‑404A, R‑407A, R‑407B, R‑407C, R‑407F, R‑410A, R‑410B, R-417A, R‑421A, R‑421B, R‑422A, R‑422B, R‑422C, R‑422D, R-424A, R‑428A, R‑434A, R‑437A, R‑438A, R‑507A, RS‑44 (2003 formulation) | Unacceptable as of January 1, 2021. |
Cold Storage Warehouses
End-Use | Prohibited Substance | Effective Date |
---|---|---|
Cold storage warehouses (new) | HFC‑227ea, R‑125/290/134a/600a (55.0/1.0/42.5/1.5), R-404A, R‑407A, R‑407B, R‑410A, R‑410B, R‑417A, R‑421A, R-421B, R‑422A, R‑422B, R‑422C, R‑422D, R‑423A, R‑424A, R-428A, R‑434A, R‑438A, R‑507A, and RS‑44 (2003 composition) | Unacceptable as of January 1, 2023. |
Vending Machines
End-Use | Prohibited Substance | Effective Date |
---|---|---|
Vending Machines (Retrofit) | R‑404A, R‑507A | Unacceptable as of January 1, 2019. |
Vending Machines (New) | FOR12A, FOR12B, HFC‑134a, KDD6, R125/290/134a/600a (55.0/1.0/42.5/1.5), R‑404A, R‑407C, R‑410A, R‑410B, R‑417A, R‑421A, R‑422B, R-422C, R‑422D, R‑426A, R‑437A, R‑438A, R‑507A, RS‑24 (2002 formulation), SP34E | Unacceptable as of January 1, 2019. |
Residential Refrigeration Appliances
End-Use | Prohibited Substance | Effective Date |
---|---|---|
Household refrigerators and freezers—compact (new) | FOR12A, FOR12B, HFC‑134a, KDD6, R‑125/290/134a/600a (55.0/1.0/42.5/1.5), R‑404A, R‑407C, R‑407F, R‑410A, R‑410B, R‑417A, R‑421A, R‑421B, R‑422A, R‑422B, R‑422C, R‑422D, R-424A, R‑426A, R‑428A, R‑434A, R‑437A, R‑438A, R‑507A, RS-24 (2002 formulation), RS‑44 (2003 formulation), SP34E, and THR-03 | Unacceptable as of January 1, 2021. |
Household refrigerators and freezers—non- compact or built-in appliances (new) | FOR12A, FOR12B, HFC‑134a, KDD6, R‑125/290/134a/600a (55.0/1.0/42.5/1.5), R‑404A, R‑407C, R‑407F, R‑410A, R‑410B, R‑417A, R‑421A, R‑421B, R‑422A, R‑422B, R‑422C, R‑422D, R-424A, R‑426A, R‑428A, R‑434A, R‑437A, R‑438A, R‑507A, RS-24 (2002 formulation), RS‑44 (2003 formulation), SP34E, and THR-03 | Unacceptable as of January 1, 2022. |
Household refrigerators and freezers—built in appliances (new) | FOR12A, FOR12B, HFC‑134a, KDD6, R‑125/290/134a/600a (55.0/1.0/42.5/1.5), R‑404A, R‑407C, R‑407F, R‑410A, R‑410B, R‑417A, R‑421A, R‑421B, R‑422A, R‑422B, R‑422C, R‑422D, R-424A, R‑426A, R‑428A, R‑434A, R‑437A, R‑438A, R‑507A, R-S24 (2002 formulation), RS‑44 (2003 formulation), SP34E, and THR-03 | Unacceptable as of January 1, 2023. |
Chillers
End-Use | Prohibited Substance | Effective Date |
---|---|---|
Centrifugal chillers (new) | FOR12A, FOR12B, HFC-134a, HFC‑227ea, HFC‑236fa, HFC245fa, R-125/134a/600a (28.1/70/1.9), R‑125/290/134a/600a (55.0/1.0/42.5/1.5), R‑404A, R‑407C, R‑410A, R‑410B, R‑417A, R‑421A, R‑422B, R‑422C, R‑422D, R‑423A, R‑424A, R‑434A, R-438A, R‑507A, RS-44 (2003 composition), and THR-03 | Unacceptable as of January 1, 2024, except where allowed under a narrowed use limit. |
Centrifugal chillers for military marine vessels (new) | HFC-134a | Acceptable after January 1, 2024 where reasonable efforts are made to ascertain that other alternatives are not technically feasible due to performance or safety requirements. |
Centrifugal chillers for human-rated spacecraft and related support equipment (new) | HFC-134a and R-404A | Acceptable after January 1, 2024 where reasonable efforts are made to ascertain that other alternatives are not technically feasible due to performance or safety requirements. |
Positive displacement chillers (new) | FOR12A, FOR12B, HFC‑134a, HFC‑227ea, KDD6, R125/134a/600a (28.1/70/1.9), R‑125/290/134a/600a (55.0/1.0/42.5/1.5), R‑404A, R‑407C, R‑410A, R‑410B, R‑417A, R‑421A, R‑422B, R‑422C, R‑422D, R‑424A, R‑434A, R‑437A, R-438A, R‑507A, RS‑44 (2003 composition), SP34E, and THR-03 | Unacceptable as of January 1, 2024, except where allowed under a narrowed use limit. |
Positive displacement chillers for military marine vessels (new) | HFC-134a | Acceptable after January 1, 2024 where reasonable efforts are made to ascertain that other alternatives are not technically feasible due to performance or safety requirements. |
Positive displacement chillers for human-rated spacecraft and related support equipment (new) | HFC-134a and R-404A |
[1] Under the narrowed use limit, use is limited to military or space- and aeronautics-related applications where reasonable efforts have been made to ascertain that other alternatives are not technically feasible due to performance or safety requirements.
[2] Low pressure two-component spray foam kits manufactured or before January 1, 2025, may be used after that date.
[3] See Footnote 2.
[4] One-component foam sealant cans manufactured on or before January 1, 2020, may be used after that date.
[5] “Medium-temperature” refers to equipment that maintains food or beverages at temperatures above 32°F (0 °C).
[6] “Low-temperature” refers to equipment that maintains food or beverages at temperatures at or below 32°F (0 °C).