EL DORADO COUNTY AIR QUALITY MANAGEMENT DISTRICT
RULE 222 - ABRASIVE BLASTING
(Adopted by Reference 1976, Revised February 1984, Adopted May 16, 1990 (State ARB)
- "Abrasives" means any material used in abrasive blasting operations including
but not limited to sand, slag, steel shot, garnet or walnut shells.
- "Abrasive blasting" means the operation of cleaning or preparing a surface
by forcibly propelling a stream of abrasive material against the surface.
- "Abrasive blasting equipment" means any equipment utilized in abrasive blasting
operations.
- "Air contaminant" includes smoke, charred paper, dust, soot, grime, carbon,
fumes, gases, odors, particulate matter, acids or any combination thereof.
- "Certified abrasive" means an abrasive which has been certified by the Air
Resources Board (ARB) in accordance with Section 92530.
- "Cut-point for fineness" means the smallest United States standard sieve
size through which no more then one percent by weight of abrasive material will pass before blasting when tested
in accordance with California Test Method No. 202-G. dated July 1, 1982.
- "Hydroblasting" means any abrasive blasting using high pressure liquid as
the propelling force.
- "Multiple nozzles" means more than one nozzle being used to abrasive blast
the same surface in such close proximity that their separate plumes are indistinguishable.
- "Permanent building" means a building which is used, in whole or in part,
for sandblasting operations.
- "Person" means any individual, firm, association, organization, partnership,
business trust, corporation, company, contractor, supplier, installer, user or owner, or any state or local governmental
agency or public district or any officer or employee thereof. "Person" also means the United States Government
or its agencies to the extent authorized by federal law.
- "Sandblasting" means abrasive blasting.
- "Source" means the impact surface from any single abrasive blasting nozzle.
- "Steel or iron shot/grit" means abrasives which meet either the Society
of Automotive Engineers (SAE) recommended practices J827 and J444 or Steel Founders' Society of America Standards
21-68 or 2OT-66, as those practices and standards existed on 2-24-84.
- "Sweep abrasive blasting" means a method of cleanup performed in order to
achieve surface uniformity or impurity removal after wet blasting, hydroblasting, or vacuum blasting operations.
- "Vacuum blasting" means any abrasive blasting in which the spent abrasive,
surface material, and dust are immediately collected by a vacuum device.
- "Wet abrasive blasting" means any abrasive blasting using compressed air
as the propelling force, which in the judgment of the air pollution control officer uses an amount of water adequate
to minimize the plume to comply with the requirements of Section 92200, Title 17, California Code and Regulations.
NOTE: Authority cited: Sections 39600 and 39601, Health and
Safety Code. Reference: Sections 41900, 41902, 41904, and 41905, Health and Safety Code.
222.2 - PROHIBITIONS
222.2a Visible Emission Standards
- No person shall discharge into the atmosphere from any abrasive blasting which is
conducted outside a permanent building any air contaminant for a period of periods aggregating more than three
minutes in any one hour which is:
- As dark or darker in shade as that designated as No. 2 on the Ringelmann Chart, as
published by the United States Bureau of Mines, or
- Of such opacity as to obscure an observer's view to a degree equal to or greater than
does smoke described in subdivision (a)(1).
- No person shall discharge into the atmosphere from any abrasive blasting which is
conducted within any permanent building any air contaminant for a period or periods aggregating more than three
minutes in any one hour which is:
- As dark or darker in shade as that designated as No. 1 on the Ringelmann Chart, as
published by the United States Bureau of Mines, or
- Of such opacity as to obscure an observer's view to a degree equal to or greater than
does smoke described in subdivision (b) (1).
NOTE: Authority cited: Sections 39600 and 39601, Health and
Safety Code. Reference: Sections 41900, 41902, 41904, and 41905, Health and Safety Code.
222.3 NUISANCE PROHIBITION
Compliance with all rules and regulations in this subchapter does not exempt any person
from complying with Section 41700 of the Health and Safety Code, nor from complying with any state statutory or
common law nuisance prohibition.
NOTE: Authority cited: Sections 39600 and 39601, Health and Safety
Code. Reference: Sections 41900, 41902, 41904, and 41905, Health and Safety Code.
222.4 COMPLIANCE WITH PERFORMANCE STANDARDS
No person shall conduct any abrasive blasting operation without complying with the performance
standards described in Article 4.
NOTE: Authority cited: Sections 39600 and 39601, Health and Safety
Code. Reference: Sections 41900, 41902, 41904, and 41905, Health and Safety Code.
222.5 SOURCE EVALUATION
222.5a Visible Emission Evaluation Techniques
Visible emission evaluation of abrasive blasting operations shall be conducted in accordance
with the following provisions:
- Emissions shall be read in opacities and recorded in percentages.
- The light source should be at the rear of observer during daylight hours.
- The light source should be behind the emission during hours of darkness.
- Observer position should be at approximately right angles to wind direction, and at
a distance no less than twice the height of the source but not more than one quarter of a mile from the base of
the source.
- Emissions from blasting which is conducted outside a permanent building shall be read
at a point in the emissions which is (1) twenty-five feet from the source; or (2)
at the densest point of the emission after a major portion of the spent abrasive has fallen out, whichever is greater;
provided, however, that emissions may be read from a greater distance than either (1) or (2), if the observer reasonably
determines that the greater distance will not significantly affect the reading.
- Where an owner or operator demonstrates that the presence of uncombined water is the
only reason for a failure to meet the limitations of Section 92200, that Section shall not apply.
- Emissions from blasting which is conducted outside a permanent building and which
employs multiple nozzles shall be judged as a single source unless it can be demonstrated by the owner or operator
that each nozzle, evaluated separately, meets the emission and performance standards provided for in this subchapter.
The owner or operator shall be offered the opportunity to make such a demonstration.
- Emissions from blasting which is conducted within a permanent building shall be read
at the densest point after the air contaminant leaves the building.
NOTE: Authority cited: Sections 39600 and 39601, Health and
Safety Code. Reference: Sections 41900, 41902, 41904, and 41905, Health and Safety Code.
222.6 PERFORMANCE STANDARDS
222.6a General Provisions
- Except as provided in subdivision (b), all abrasive blasting operations shall be conducted
within a permanent building.
- An abrasive blasting operation conducted under one or more of the following conditions
is not required to be conducted within a permanent building.
- Steel or iron shot/grit is used exclusively;
- The item to be blasted exceeds 8 feet in any dimension; or
- The surface being blasted is situated at its permanent location or no further away
from its permanent location than is necessary to allow the surface to be blasted.
- Except for testing conducted in accordance with Section 92530 (b)(1)(B) and as otherwise
provided in Sections 92510 or 92520, any abrasive blasting operation conducted
in accordance with subsections (b)(2) and (b)(3) outside a permanent building must use exclusively:
- Wet abrasive blasting;
- Hydroblasting;
- Vacuum blasting; or
- Abrasive certified for permissible dry outdoor blasting.
NOTE: Authority cited: Sections 39600 and 39601, Health and
Safety Code. Reference: Sections 41900, 41902, 41904, and 41905, Health and Safety Code.
222.7 PAVEMENT MARKING
Surface preparation for raised traffic delineating markers and pavement marking removal
using abrasive blasting shall comply with at least one of the following performance standards:
- Wet abrasive blasting, hydroblasting, or vacuum blasting shall be used;
- Dry abrasive blasting for removal or surface preparation for immediate application
of pavement markings of less than 1,000 square feet or for surface preparation for raised traffic delineating markers
shall use certified abrasives.
NOTE: Authority cited: Sections 39600 and 39601, Health and
Safety Code. Reference: Sections 41900, 41902, 41904, and 41905, Health and Safety Code.
222.8 STUCCO AND CONCRETE
Abrasive blasting of stucco and concrete shall be performed by wet blasting, hydroblasting,
or vacuum blasting with the following exceptions:
Dry blasting with a certified abrasive may be used for:
- (a) Window and door returns and frames;
- (b) Eaves, overhangs, and ceilings;
- (c) Sweep abrasive blasting except for stucco surfaces;
- (d) Completely shrouded structures or blast areas that effectively control emissions;
- (e) Abrasive cleaning operations, other than aggregate exposure or paint removal
related to new concrete construction or repair activity, if such operations are performed onsite.
NOTE: Authority cited: Sections 39600 and 39601, Health and Safety Code. Reference:
Sections 41900, 41902, 41904, and 41905, Health and Safety Code.
222.9 CERTIFIED ABRASIVES
- The ARB shall certify abrasives which comply with the performance standards set forth
in subdivision (b) below. Any person who desires certification of an abrasive shall furnish to the ARB an adequate
test sample, together with fees to defray the cost of testing. Each certification of an abrasive shall include
the ARB's determination of the original cut-point for fineness of the abrasive. The ARB shall maintain an up-to-date
list of certified abrasives. Certification shall not be effective for more than two years. Abrasive materials which
are certified on the effective date of this section shall remain certified until September 1, 1992.
- Performance Standards.
-
- Before blasting the abrasive shall not contain more than one percent by weight material
passing a #70 U.S. Standard sieve when tested in accordance with "Method of Test for Abrasive Media Evaluation."
Test Method No. California 371-A, dated May 15, 1975.
- If the abrasive does not meet the requirements of subdivision (b)(1)(A), the person
who desires certification of the abrasive may as an alternative demonstrate within the State of California to the
satisfaction of the ARB that the abrasive meets a 20 percent opacity emission limit when tested in accordance with
the "Visible Emission Evaluation Test Method for Selected Abrasives Used in Permissible Dry Outdoor Blasting,"
as adopted by the ARB and incorporated herein by reference. The person who desires certification of the abrasive
shall be solely responsible for conducting the demonstration.
- After blasting, the abrasive shall not contain more than 1.8 percent by weight material
5 microns or smaller when tested in accordance with "Method of Test for Abrasive
Media Evaluation" Test Method No. California 371-A, dated May 15, 1975.
- A used certified abrasive shall not be considered certified for reuse unless the abrasive
conforms to its original cut-point for fineness.
- A blend of certified abrasives shall be considered certified for purposes of Section
92530(a) unless found not to meet the requirements of Section 92530(b) pursuant to testing initiated by the ARB.
- All manufacturers and suppliers of certified abrasives shall legibly and permanently
label the invoice, bill of lading and abrasive packaging or container with each of the following:
- The manufacturer's name or identification trade name,
- The grade, weight proportion of components in abrasive blends, brand name of the abrasive
or brand names and grades of components of abrasive blends, and
- The Statement "ARB certified for permissible dry outdoor blasting." This
subsection shall become effective six months September 1, 1992.
NOTE: Authority cited: Sections 39600 and 39601, Health and
Safety Code. Reference: Sections 41900, 41902, 41904, and 41905, Health and Safety Code.